Story image

Electrical distribution safety & reliability: Get it right from the start

09 Oct 2017

Electrical distribution systems are found supplying power in all sorts of factories, data centers, hospitals, and large commercial complexes.

The reliability of these systems is critical to keeping businesses and services running smoothly.

So, when a failure occurs, the first inclination of the facility team might be to blame some aspect of the system, including the manufacturer.

However, though the electrical switchgear may be the point at which a problem is most visible, the source of the problem may be elsewhere or, in fact, much earlier.

This is because the reliable performance of an electrical distribution system goes beyond the equipment itself. It is also greatly dependent on safety-related considerations during the design and installation phase, as well as during operation and maintenance.

For specifying engineers, delivering system designs with the highest possible power availability and safety requires identifying and mitigating every risk.

For facility teams, operational and maintenance practices that address all risk factors are key to enhancing reliability and safety while minimizing costs over the entire life cycle of the system.

Standards - like IEC 61936-1 for medium voltage (MV) systems and IEC 60364 series for low voltage (LV) systems - as well as local regulations provide a sound basis for installation design.

But they don’t address every unique aspect of every location. There could be remaining risks that need to identified and mitigated.

So let’s have a look at some of these potential risks, specifically for MV systems, and some best practices that can help avoid them.

Please note this is a brief overview. 

Arc faults, shocks, and accidents

An arc fault can be caused by a few different factors, including aging insulation, a foreign object, or an overvoltage. If large enough, it can damage the installation and harm people. The IEC 62271-200 standard specifies possible arc fault locations, causes, and preventative measures.

Specifying ‘arc-classified’ switchgear will help limit exposure to arc effects on nearby personnel; however, it not enough to address all possible situations.

To ensure performance isn’t compromised, the installation conditions defined by the manufacturer need to be respected.

Standards and regulations that address installation procedures define minimum clearances to avoid accidental contact with bare, live conductors. But some situations may pose risks not addressed by the regulations. Procedures for ‘live work’ make personnel more aware of the dangers, and thus accidents rarely occur.

However, the possibility of indirect contact with an accidentally energized part is also a serious threat. These ‘step’ or ‘touch’ voltages are due to lack of effective grounding.

Designs rules for grounding systems provide good protection, but only if connections remain effective and the values used for calculation are not exceeded.

Beyond electrical accidents, mishaps can include falling from ladders or other high places, collision with equipment due to lack of working space, and injuries due to moving heavy loads without proper lifting tools. That’s why it’s a best practice to review all tasks, ensure enough free space is available for each, and document all recommended tools and procedures.

Environmental and electrical conditions over time

The environmental conditions electrical equipment operates in can greatly affect its performance and reliability. Uncontrolled humidity can be the most detrimental factor, along with temperature, dust, and corrosive gases.

Therefore the design of the electrical room should take these factors into consideration, as well as the need for monitoring and control of temperature and humidity.

Any plan for ventilation should avoid the possible negative effects of cold, damp, and dust on MV switchgear.

The rated characteristics of an electrical installation are set at the design stage based on the forecasted service. However, changes can occur over the service life, such as the addition of loads, cables, or capacitors.

Or maybe there’s been a higher than expected level of lightning strikes.

This could push the system beyond its ratings, increasing risk of failure.

So it’s important to periodically review and document electrical conditions and any evolutions that have occurred in the system.

Article by Didier Fulchiron, Scneider Electric Data Center Blog 

Unencrypted Gearbest database leaves over 1.5mil shoppers’ records exposed
Depending on the countries and information requirements, the data could give hackers access to online government portals, banking apps, and health insurance records.
SAS announces US$1 billion investment in AI
"At SAS, we remain dedicated to our customers and their success, and this investment is another example of that commitment."
Two Ministers’ thoughts on blockchain in Oz
Minister Karen Andrews, and Minister Simon Birmingham have released a joint statement on the national blockchain roadmap and extra $100,000 funding.
IntegrationWorks continues expansion with new Brisbane office
The company’s new office space at the Riverside Centre overlooks the Brisbane River and Storey Bridge.
DXC subsidiary takes SAP energy industry partner award
Winners of the awards were selected from SAP’s A/NZpartner ecosystem and announced at the recent SAP A/NZ Partner Kick-Off Meeting held in Sydney.
NetApp and allegro.ai showcase an integrated solution for deep learning
Unlike traditional software, in deep learning, the data rather than the code is of the utmost importance.
Opinion: Moving applications between cloud and data centre
OpsRamp's Bhanu Singh discusses the process of moving legacy systems and applications to the cloud, as well as pitfalls to avoid.
Workflows should benefit people, not devices
It is important that, in digital transformation journeys, managers remember technology should complement, rather than overtake, employee talent and skillsets.